![velvet drive 10-17-004 rebuild kit velvet drive 10-17-004 rebuild kit](https://m.media-amazon.com/images/I/81ZYbok6b6L._AC_SL1400_.jpg)
- #VELVET DRIVE 10 17 004 REBUILD KIT MANUALS#
- #VELVET DRIVE 10 17 004 REBUILD KIT MANUAL#
- #VELVET DRIVE 10 17 004 REBUILD KIT SERIES#
If you can, take pictures as you go in case you forget how/when a particular part came out. Stage the parts in order as you are pulling them out to remember how they go back in. This thread does not cover reduction ratios.
#VELVET DRIVE 10 17 004 REBUILD KIT MANUAL#
Ě feeler gauge 0.018" to 0.055" (to set clutch clearance)ĭifferent manual attached to this post.
![velvet drive 10-17-004 rebuild kit velvet drive 10-17-004 rebuild kit](https://images2.heavydutykits.com/wp-content/uploads/2020/06/alto-marine-parts.jpg)
The usual assortment of torque wrench(es), socket (hex but also at least one 3/8" 12 points socket), etc. Reverse Clutch Kit 71C & 72C, Kawasaki Starter Clutch Repair Rebuild Kit z1. Ěn arbor press (mainly to compress the clutch pack) If your looking for Velvet Drive Marine Transmission Parts online lookup. By changing the clutch disc material and the number of clutch disc.
#VELVET DRIVE 10 17 004 REBUILD KIT MANUALS#
Use the appropriate instructions given in the 71 C and 72C service manuals when servicing the 10-17 and 10-18 transmissions. We have reengineered the Velvet Drive transmission for high performance and durability.
#VELVET DRIVE 10 17 004 REBUILD KIT SERIES#
skidim.) I have no affiliation with ebasic. SERIES 10-17 AND 10-18 SERVICE INSTRUCTIONS Practically all information which has been written for the 71 C and 72C Velvet Drive transmissions applies to the 10-17 and 10-18 assemblies.
![velvet drive 10-17-004 rebuild kit velvet drive 10-17-004 rebuild kit](https://bpi.ebasicpower.com/mm5/graphics/00000001/ALT23901VD.jpg)
(All these parts are also available elsewhere (i.e. Ĝomplete snap ring set or at least front bearing snap ring: Rebuild kit (includes forward and reverse clutch plates, seals and gaskets) I decided, it was time for a rebuild, so here goes the write-up: 071″ are to be used in any 1017- or 1018-transmission.ġ018-003 through 1018-106 use 2 steel and 3 friction plates.After changing the ATF fuid of my velvet drive 71c (model 10-17-004) (which had probably never been changed) the transmission started slipping severely. They are no longer used in any Velvet-Drive transmission. * The 6 was originallybuilt with 2 special steel plates and one friction plateVelvet Drive recommends changing this configuration to 1 steel and two frictionIf the steel plates removed are. NOTE: The following kits are available for the Model 71 C and 72C transmissionsIndex numbers shown match the index numbers on the Above exploded-view *** CHECK MODEL CHART ON VELVET DRIVE PAGE TO DETERMINE CORRECT PART NUMBER Velvet Drive Gasket and Seal Kit Velvet Drive 71C & 72C Item :023801B. Overhaul Kit, Complete Borg Warner 71/72C All Ratios Item :023901. **REFER TO REDUCTION SECTION IN BACK OF MANUAL. Borg Warner Velvet Drive 72C 1:1 Transmission (new) Item :RA157003. *SEE CHART ON PAGE 34 TO DETERMINE PROPER AMOUNT. Note 1: REFER TO ASSEMBLY NUMBER ON ID TAG (See Figure 1) NSS – NOT SERVICED SEPERATELY, BUY NEXT HIGHER ASSEMBLY THRUSTWASHER (USE W/SEALING RING STYLE CASE)įLAT WASHER, EARLY MODELS, NO LONGER USED SNAP RING(.062-.066 THICK) (10-18 ONLY) (Purple) Maximize strength with the right gasket and seal kit for Borg Warner Velvet Drive 71 and 72 series transmissions. To Visit the Online Store Select This Link Transmission Pricing